RØDE Microphones - VideoMic Pro
<iframe width="800" height="483" src="https://www.youtube.com/embed/O4lE6Mrj81Q" frameborder="0" gesture="media" allowfullscreen></iframe>
RØDE Microphones - VideoMic Pro

RØDE Microphones - VideoMic Pro

Taxes and shipping calculated at checkout

Stock Notification

Get notified when this product is available again

Frequently Bought Together

Have a question?

RØDE Microphones - VideoMic Pro

  •     Rycote® Lyre® shock mounting onboard
  •     All-new capsule with lower noise and higher sensitivity
  •     Broadcast recording quality condenser microphone
  •     Compact form factor (150mm/6” length)
  •     Ultra lightweight (85g/3oz)
  •     9V battery powered - over 70 hours use (alkaline)
  •     Integrated shock mounting
  •     Integrated foam windscreen
  •     3.5mm stereo mini-jack output (dual mono)
  •     Two step High Pass Filter (flat, 80Hz)
  •     Three position level control (-10dB, 0, +20dB)
  •     Camera shoe mount with 3/8” thread for easy boompole mounting
  •     10 year extended warranty when you register your microphone

The RØDE VideoMic Pro is a true shotgun microphone designed for use with camcorders, DSLR cameras and portable audio recorders as a source of primary and reference audio.

At the heart of the VideoMic Pro is an all-new 1/2" condenser capsule that provides broadcast-quality audio via a 3.5mm minijack connector (outputting the mono signal to both left and right channels) with an incredibly low self-noise of just 14db. A super-cardioid polar pattern ensures that surrounding audio is minimised, and your recording is focused on the subject in front of the camera.

The integrated Rycote® Lyre® based shock mounting system separates the VideoMic Pro capsule and electronics from its mount, providing isolation from external physical factors that may cause unwanted rumble and vibrations in the microphone. Constructed from a single piece of hard-wearing thermoplastic, the Lyre® provides superior acoustic suspension to traditional elastic solutions, and will never wear out, sag or snap.

Easily accessible on the rear face of the microphone are the power, filter and level controls. In addition to the microphone's native 40Hz-20kHz response a selectable high-pass filter at 80Hz is available, which will prevent low end noise such as air conditioners and traffic from being recorded.

Below these controls are the level settings, which attenuate or boost the recorded level as required. The -10dB level attenuation (or PAD) is ideal for recording loud sound sources, such as live music, motorsport, or interviews where the subject is very close to the camera. The +20dB level boost is designed for use with DSLR cameras, allowing the user to reduce the camera's preamp level (or mic-input level), effectively reducing the amount of noise generated by the camera's comparatively low quality audio circuitry.

The microphone uses a standard sized shoe mount for on camera use, and features a 3/8" thread in the base of the mount for easy boom pole mounting.

The VideoMic pro is battery powered, and provides over 70 hours recording from a single 9V battery.

The RØDE VideoMic is designed and made in Australia, and covered by RØDE Microphones' industry leading 10 year warranty.

VideoMic Pro Specifications

Acoustic Principle    Line Gradient
Active Electronics    JFET impedance converter
Capsule    0.50"
Address Type    End
Frequency Range    40Hz - 20kHz (selected HPF @80)
Output Impedance    200Ω
Maximum SPL    134dBSPL
Maximum Output Level    6.9mV (@ 1kHz, 1% THD into 1KΩ load)
Sensitivity    -32.0dB re 1 Volt/Pascal (20.00mV @ 94 dB SPL) +/- 2 dB @ 1kHz
Equivalent Noise Level (A-weighted)    14dBA
Weight     85g
Dimensions    100mmH x 75mmW x 170mmD
Warranty     1 year with free extension to 10 years

Shipping costs are calculated at time of checkout by our shopping cart, based on the weight of your order and the method of shipment.

View All

Recommended for You

Your recently viewed items